Archive for March, 2008
Here you will find a collection of photos of 1968 Honda CT90 Trail bikes posted by different owners.
View Page »
Here you will find a collection of photos of 1968 Honda CT90 Trail bikes posted by different owners.
View Page »
Here you will find a collection of photos of 1969 Honda CT90 Trail bikes posted by different owners.
View Page »
Here you will find a collection of photos of 1970 Honda CT90 Trail bikes posted by different owners.
View Page »
Here you will find a collection of photos of 1971 Honda CT90 Trail bikes posted by different owners.
View Page »
Here you will find a collection of photos of 1972 Honda CT90 Trail bikes posted by different owners.
View Page »
Starting the Bike
When starting a CT-90 or CT-110, you should know a couple of things.
First, this is a carbureted engine, and second, it has an automatic clutch. Most well-maintained CTs are quite easy to start. My 110 often starts on the first or second kick after being stored without fuel all winter. My old 1970 CT-90 was so gentle it could be started with your hand. However, some CTs can require a little more effort.
View Page »
Part Name |
Model or Year |
Where to Buy |
inline fuel filter |
all |
Wix # 33011 / NAPA 3011 fuel |
View Page »
Part Name |
Model or Year |
Where to Buy |
More About this Part… |
Unifilter BF-1 Bulk Air Filter Foam |
Later CT-90s and probably CT-110s. I used on a 1975. |
AZ Motorsports, MotorHelmets, RepairManual |
2 filters from 1 pkg if you are careful. Cut and form tube using silicone seal. |
View Page »
Part Name |
Model or Year |
Where to Buy |
Substitute Part |
Tail-light |
All 6Volt |
Canadian Tire |
MotoMaster part no. 20-2628-8 |
Part Name |
Model or Year |
OEM? |
Where to Buy |
More About this Part… |
Muffler rust hole fix |
Any |
JB Weld |
Almost any Home Center |
Lightly sand the area around the rust hole. If hole is larger than 1/2 ” in diameter , put scotch tape over hole. Be sure sanded area extends past the tape. Mix JB Weld and use a large tounge depresser (or similar) to spread the JB Weld over the area of the tape and on to the sanded area. |
View Page »
Part Name |
Model or Year |
Where to Buy |
More About this Part… |
Kopr-Shield |
Any |
Eastwood Co. |
This is a copper-based contact paste used to reduce electrical resistance and cortrosion, and is helpful on CT90 bullet connectors and such. Vic Barkas |
View Page »
Part Name |
Model or Year |
Where to Buy |
Substitute Part |
More About this Part… |
Jasco Metal Etch (fuel tank cleaning) |
Any |
Most hareware stores (Paint dept.) Cheap! |
Contains phosphoric acid, same as Naval Jelly |
Use undilluted quart in tank, leave 24hrs, aggitating & turning tank several times. Save and reuse. Rinse tank out with gasoline. |
Part Name |
Model or Year |
More About this Part… |
Headlight bucket |
ct200, c200 and ct90K0 |
The plastic headlight bucket that goes over the front fender is the same on these three bikes. |
Part Name |
Model or Year |
Where to Buy |
Substitute Part |
More About this Part… |
Fibre Washer for under carb top cap |
CT90 |
Home Depot, Lowes, Rona or hardware store in specity item area in screw dept. |
Manufactured by Lincoln Products – Industry, CA 91748 – Part # 129390 |
Fibre Wash 3/4 x 5/8 x 1/32 – comes in plastic envelope measuring 3 x 3 inch. |
View Page »
|